banner
Home » Product > Emc LED > EMC 3030 SMD LED
Product Categories

3030 SMD LED Series

● Viewing angle:120 deg
● The materials of the LED dice is InGaN
● 3.20mm×3.00mm×0.6mm
● RoHS compliant lead-free soldering compatible

Send InquiryChat Now


 Feature

 

Viewing angle:120 deg                        

The materials of the LED dice is InGaN          

3.20mm×3.00mm×0.6mm                      

RoHS compliant lead-free soldering compatible   

 


 Package Outline    

Unit:mm

image001(001).jpg

●Absolute maximum ratings                                           Ta=25±3

Parameter

Symbol

Value

 

Unit

 

Power dissipation

Pd

1

W

Forward current

If

350

mA

Reverse voltage

Vr

5

V

Operating temperature range

Topr

-20~+85

Storage temperaturer range

Tstg

-40~+100

Junction Temperature

Tj

100

Pulse Forward Current

Ifp

450

mA

Electrostatic Discharge

ESD

2000(HBM)

V


●Electro-optical characteristics                                         Ta=25±3

Parameter

Test Condition

 

Symbol

 

Value

Unit

 

Min.

 

Typ.

 

Max.

Forward voltage

 

If=60 mA

Vf

2.6

--

2.9

V

Luminous intensity

 

If=60 mA

Φ

33

--

35

Lm

Viewing angle 50% Iv

If=60 mA

2θ 1/2

--

120

--

Deg

Reverse current

 

Vr=5V

Ir

--

--

10

μA

ColorTemperature

 

If=60 mA

TC

4000

--

4500

K

Chromaticity CIE

 

If=60 mA

CIE


CRI

 

If=60 mA

Ra

70

 

NOTES: 




1.Luminous Flux measurement tolerance:±10%


2.Forward Voltage measurement tolerance:±0.1V


3.Color Temperature measurement tolerance:x,y±0.01


4.CRI measurement tolerance:±2




 Typical optical characteristics curves

图片29.png


图片30.png


图片31.png

图片32.png

图片33.png

图片33.png


 Intensity Bin Limit (If=60 mA) 

Bin code

Flux(lm) for reference

Min

Max

1

33

35


 VF Bin Limit (IF = 60 mA)

Bin code

Min.(V)

Max.(V)

1

2.6

2.7

2

2.7

2.8

3

2.8

2.9


 Chromaticity CIE 

图片1.png


Requirements for application and reflow soldering


Reflow Soldering

Pre-heat

 

120~160

Pro-heat time

 

120 seconds Max.

 

Peak temperature

 

260℃ Max.

 

Soldering time

 

10 seconds Max.

 

Condition

 

Refer to Temperature-profile


After reflow soldering rapid cooling should be avoided

Temperature-profile(Surface of circuit board)  

Use the following conditions shown in the figure.  

                                                  <Pb-free solder>  

图片2.png

1.Reflow soldering should not be done more than two times    

2.When soldering,do not put stress on the LEDs during heating


Application:

●Indoor gardening photocatalyst germicidal lamp (mainly for  Strawberry, Tobacco etc.)

●Portable money-counting torches and mosquito lamps

●Beauty lamps, fishing lamp, stage lighting for entertainment

●UV curing use and smart lamps and lanterns

●Medical lamps

●Widely used in lighting area


image003.jpg


Packaging & Delivery

 Packaging  Details
 4000pcs/reel, each reel Anti-static vacuum  Bag


 Delivery  Time
 Shipped in 3-5 days after payment


 image005.jpg




Handling Precautions

Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.

 

♦ Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.

♦ Not suitable to operate in acidic environment, PH<7.

 

♦ LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.

 

When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine 

element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than  375 PPM.

 

♦ The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.

 

♦ Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

 

Storage

♦ Before opening the package, the LEDs should be kept at 30 or less and 60%RH or less. The LEDs shouldbe used within a year.

 

♦ After opening the package, the product should be stored at 30 or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.


Our Services: 

 1. 3 years warranty
 2. strict  quality control system for smd 3030 led 
 3. professional sales team
 4. Reply letters or inquirieds within 24 hours. 
 5. We will  try our best to offer you the best service from pre-sales to customer  service as we promised. 


FAQ:

 1.Prices conditions
 Price can be FOB, CIF ,EXW, or With  taxes 


 2.What will be the delivery time and what will be the mode of payment?
 We have large quantities in Stock for  normal color,Normal size ,for special color and products sizes it need to 3-5  days to customize.50K units is available for most of our models in normal color  and sizes
 The payment can be T/T  transaction,Letter of credit,Paypal,Western Union 


 3.Shipment will be over sea or by air?
 Generally speaking ,we ship the products by DHL UPS FEDEX express since  the products isn’t too heavy for the transportation


 4.Could you please send me the sample for the same.So that i could see and analyze its quality?
  Yes.We can send samples first,samples need to be charged  if the value is higher 

 

Company

3.jpg


Patents

zhengshu副本(001).jpg


Contact:

Alisa Huang

Guangdong Elite Optoelectronic Technology Co., LTD

Mobilephone:+86-18033336027

Tel:0769-89080660-824

Fax:0769-89080658

Email:ruilu_sales1@elitebm.com


Contact: Carol Chen

Mobilephone:+86-13798703095

Telephone:+86-769-88941998

Email:elite1@elitebm.com


image022.jpg


Hot Tags: 3030 SMD LED series, China, suppliers, manufacturers, price

Inquiry