banner
Home » Product > Emc LED > EMC 3030 SMD LED
Product Categories

Datasheet of SMD 3030 Chip LED

​●IS09001:2008 Factory, SGS/ TUV Audited Factory
●140-160LM/W, Energy Saving over 50%
●Excellent Color Consistency.(Two times of color seperation process)
●Brightness Decay can be as low as 3%.
●Equipped with 16 automatic production lines. ( Production capacity: 10KK high power led/month, 30kk smd led/month.)

Send InquiryChat Now


 Feature

 

Viewing angle:120 deg                        

The materials of the LED dice is InGaN          

3.20mm×3.00mm×0.6mm                      

  RoHS compliant lead-free soldering compatible



image002.jpg

 





●Absolute maximum ratings                                           Ta=25±3


Parameter

Symbol

Value

 

Unit

 

Power dissipation

Pd

1

W

Forward current

If

350

mA

Reverse voltage

Vr

5

V

Operating temperature range

Topr

-20~+85

Storage temperaturer range

Tstg

-40~+100

Junction Temperature

Tj

100

Pulse Forward Current

Ifp

450

mA

Electrostatic Discharge

ESD

2000(HBM)

V


●Electro-optical characteristics                                         Ta=25±3


Parameter

Test Condition

 

Symbol

 

Value

Unit

 

Min.

 

Typ.

 

Max.

Forward voltage

 

If=60 mA

Vf

2.6

--

2.9

V

Luminous intensity

 

If=60 mA

Φ

33

--

35

Lm

Viewing angle 50% Iv

If=60 mA

2θ 1/2

--

120

--

Deg

Reverse current

 

Vr=5V

Ir

--

--

10

μA

ColorTemperature

 

If=60 mA

TC

4000

--

4500

K

Chromaticity CIE

 

If=60 mA

CIE


CRI

 

If=60 mA

Ra

70

 

NOTES: 




1.Luminous Flux measurement tolerance:±10%


2.Forward Voltage measurement tolerance:±0.1V


3.Color Temperature measurement tolerance:x,y±0.01


4.CRI measurement tolerance:±2





 Typical optical characteristics curves

图片29.png

图片30.png

图片31.png

图片32.png

图片33.png

图片34.png




 Intensity Bin Limit (If=60 mA) 


Bin code

Flux(lm) for reference

Min

Max

1

33

35


 VF Bin Limit (IF = 60 mA)



Bin code

Min.(V)

Max.(V)

1

2.6

2.7

2

2.7

2.8

3

2.8

2.9


 Chromaticity CIE


图片1.png




 Color Bin Limit (IF = 60 mA)




Requirements for application and reflow soldering

Reflow Soldering

Pre-heat

 

120~160

Pro-heat time

 

120 seconds Max.

 

Peak temperature

 

260℃ Max.

 

Soldering time

 

10 seconds Max.

 

Condition

 

Refer to Temperature-profile


After reflow soldering rapid cooling should be avoided

Temperature-profile(Surface of circuit board)  

Use the following conditions shown in the figure.  

                                    <Pb-free solder> 

图片2.png


1.Reflow soldering should not be done more than two times    

  2.When soldering,do not put stress on the LEDs during heating




Handling Precautions

Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.

 

 Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.

 Not suitable to operate in acidic environment, PH<7.

 

 LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.

 

When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine 

element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than  375 PPM.

 

 The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.

 

 Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

 

Storage

 Before opening the package, the LEDs should be kept at 30 or less and 60%RH or less. The LEDs shouldbe used within a year.

 

 After opening the package, the product should be stored at 30 or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.


Packaging & Delivery

Packaging Details

4000pcs/reel, each reel Anti-static vacuum Bag


Delivery Time

Shipped in 3-5 days after payment


image006.jpg

 

image008.jpg

 

FAQ:

1.What will be the delivery time?

A:We have large quantities in stock for normal color and size ,and for special color and size.It needs 3-5 days to customize.100K units is available for most of our models in normal color and size.

 

2.What will be the price terms?

A: We can accept FOB, EXW, CIF normally and other terms according to customers special requirement.

 

3. What will be the types of payment?

A: The payments we can accept are T/T transaction, Paypal, Western Union, Escrow, Money Gram and Chinese bank.

 

4. what is the color temperature for white light?

A:  HHE 's LED Lighting offer leds in warm, natural, pure and cool white with color temperatures measured in Kelvin (K). 

The lower the color temperature is, the warmer the light given by the LED:

*Warm white = 2700K-3500K

*Natural white = 4000K-6000K

*Pure white = 6000K-9000K

*Cool white = 9000K-20000K

5.What is CRI ( Color Rendering Index)?

A: CRI is a figure which feedback the real objects colors. Higher CRI with higher cost. For leds, the CRI is mostly 70-80Ra.

 

6.What will be the types of shipping?

A: For the shipment, you can choose DHL, UPS,TNT,EMS,ARAMEX, FedEx, Citylink line, China post, by air mail, and by sea, etc.

 

7.what relationship is between viewing angle and brightness of led?

A: For the leds with same chip, the smaller of the angle is, the brighter of the led is. Besides, the deeper of the holder dips into the lens is, the bigger of the angle is.

 

Company

3.jpg


Patents

zhengshu副本(001).jpg



image024.jpg

Alisa Huang

Guangdong Elite Optoelectronic Technology Co., LTD

Mobilephone:+86-18033336027

Tel:0769-89080660-824

Fax:0769-89080658

Email:ruilu_sales1@elitebm.com


Contact: Carol Chen

Mobilephone:+86-13798703095

Telephone:+86-769-88941998

Email:elite1@elitebm.com


Hot Tags: datasheet of SMD 3030 chip LED, China, suppliers, manufacturers, price

Inquiry