banner
Home » Product > SMD LED > SMD LED 2835
Product Categories

2835 LED Package

*The LED are available with different color
*Utilizing advanved technology
*High brightness,long life

Send InquiryChat Now

Product features:

  *The LED are available with different color
  *Utilizing advanved technology
  *High brightness,long life



Package Outline    

Unit:mm

图片36.png

NOTES:  

1. All dimensions are in millimeters;   

     2.Tolerances are±0.05mm unless otherwise noted.



Color

Luminious flux

            CCT

Viewing angle

Voltage

warm white

 

26-28LM

2800-3300K

 

 

          120°

 

 

2.9-3.1V

natural white

4000-4500K

daylight  white

5000K-5500K
     6000-6500K

cool white

>7000K

 


 Typical optical characteristics curves 

图片37.png



Requirements for application and reflow soldering

Reflow Soldering

Pre-heat

 

120~160

Pro-heat time

 

120 seconds Max.

 

Peak temperature

 

245℃ Max.

 

Soldering time

 

10 seconds Max.

 

Condition

 

Refer to Temperature-profile


After reflow soldering rapid cooling should be avoided

Use the following conditions shown in the figure.    

      <Pb-free solder>                                       <Lead solder>

图片38.png

1.Reflow soldering should not be done more than two times    

2.When soldering,do not put stress on the LEDs during heating



Handling Precautions

 

Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.

 

 Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.

 

 Do not stack together assembled PCBs containing LEDs. Impact may scratch the silicone lens or damage the internal circuitry.

 

 Not suitable to operate in acidic environment, PH<7.

 

 LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.

 

When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine 

element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than  375 PPM.

 

 The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.

 

 Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

 

Storage

 Before opening the package, the LEDs should be kept at 30 or less and 60%RH or less. The LEDs shouldbe used within a year.

 

 After opening the package, the product should be stored at 30 or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30℃or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.

 


Reliability

(1) TEST ITEMS AND RESULTS

Type

 

Test Item

 

Ref.Standard

 

Test Conditions

 

Note

 

Number of Damaged

 

Environmental

Sequence

Resistance to Soldering Heat(Reflow Soldering)

JESD22-B106

Tsld=2605sec

2 times

 

0/100

Temperature Cycle

 

JESD22-A104

-40℃30min ↑↓5min

100℃ 30min

100 cycle

 

0/100

Thermal Shock

 

JESD22-A106

-40℃15min ↑↓5min

100℃ 15min

100 cycle

 

0/100

High Temperature Storage

 

JESD22-A103

Ta=100℃

1000 hrs

 

0/100

Low Temperature Storage

JESD22-A119

Ta=-40℃

1000 hrs

 

0/100

Power temperature Cycling

JESD22-A105

On 5min -40℃15min

↑↓    ↑↓15min

Off5min 100℃15min

100 cycle

 

0/100

Operation

Sequence

Life Test

 

JESD22-A108

Ta=25℃

IF=100MA

1000 hrs

 

0/100

High Humidity Heat

Life Test

 

JESD22-A101

80℃RH=80%

IF=100MA

1000 hrs

 

0/100

2)  CRITERRIA FOR JUDGING THE DAMAGE 

Item

 

Symbol

 

Test Conditions

 

Criteria for Judgement

Min.

Max

Forward Voltage

 

VF

IF=100MA

--

U.S.L*)×1.1

Reverse Current

 

IR

VR=5V

--

U.S.L*)×2.0

Luminous Intensity

 

IV

IF=100MA

L.S.L**)×0.7


U.S.L.:Upper Standard Level              L.S.L.:Lower Standard Level


Application

●LED Panel light

●LED bulb light

●LED tube light

●LED strip light

●LED spot light etc.

 

image004.jpg

 

Packaging & Delivery

Packaging Details

4000pcs/reel, each reel Anti-static vacuum Bag


Delivery Time

Shipped in 3-5 days after payment

 

image005(010).jpg

 

Cautions:

1)Soldering Conditions

Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and Second soldering process.


2)Static Electricity

It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.All devices, equipment and machinery must be properly grounded.Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) 


3)Moisture Proof Package

It is recommended that moisture proof package be used .


4)Storage

Before opening the package ,The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be used within a year.


5)After opening the package, The LEDs should be soldered within 24 hours (1days) after opening the package.

 

FAQ:

Q1. Can I have a sample order for led light?

A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.


Q2. What about the lead time?

A:Sample needs 1-3 days, mass production time needs 5-7 days for order quantity more than 100KK.


Q3. Do you have any MOQ limit for led light order?What's the Payment way ?

A: MOQ is 100pcs for each model. We accept T/T Paypal and Western Union three ways paymant


Q4. How do you ship the goods and how long does it take to arrive?

A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 2-5 days to arrive. Airline and sea shipping also optional.


Q5. How to proceed an order for led light?

A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.


Q6. Is it OK to print my logo on led light product?

A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.


Q7: Do you offer guarantee for the products?

A: Yes, we offer 3 years warranty to our products.

  

Our Services:

●Reply your inquiry in 24 working hours

●Well-trained and experienced staffs to answer all your inquiries in fluent English.

●Strict quality control procedures before shipment.

●Customized design is available.OME and ODM are welcomed

●Delivery the goods to our customer all over the world with speed and precision.

 

Company

01.JPG02.JPG

201711161630163857395.jpg


Patents

zhengshu副本(001).jpg


Contact:

Alisa Huang

Guangdong Elite Optoelectronic Technology Co., LTD

Mobilephone:+86-18033336027

Tel:0769-89080660-824

Fax:0769-89080658

Email:ruilu_sales1@elitebm.com

 

Contact: Carol Chen

Mobilephone:+86-13798703095

Telephone:+86-769-88941998

Email:elite1@elitebm.com


Hot Tags: 2835 LED package, China, suppliers, manufacturers, price

Inquiry