1, RoHS Compliant
2, High luminous intensity output
3, Excellent character appearance
4, Low voltage and current operating
5, Ultra-low power consumption
6, Solid-state LED chip based
7, Long life-span
8, Easy mounting on printed circuit board and sockets
9, IC compatible
10, Certificates: RoHS and Reach compliant
11, Type:5630 SMD LED
Peak Forward Current
High brightness; Low power consumption; High reliability and stability;
Flexibility in optical design and mechanical design
Optical indicator; Indoor lighting; Interior automotive lighting; Backlight for LCD,switch and Symbol, display; Light pipe application; Advertisement
● Color Bin Limit (IF =150 mA)
●Requirements for application and reflow soldering
120 seconds Max.
10 seconds Max.
Refer to Temperature-profile
After reflow soldering rapid cooling should be avoided
Temperature-profile(Surface of circuit board)
Use the following conditions shown in the figure.
<Pb-free solder> <Lead solder>
1. Reflow soldering should not be done more than two times
2.When soldering,do not put stress on the LEDs during heating
(1) TEST ITEMS AND RESULTS
Number of Damaged
Resistance to Soldering Heat(Reflow Soldering)
High Temperature Storage
Low Temperature Storage
Power temperature Cycling
On 5min -40℃＞15min
High Humidity Heat
(2) CRITERRIA FOR JUDGING THE DAMAGE
Criteria for Judgement
U.S.L.:Upper Standard Level L.S.L.:Lower Standard Level
Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.
♦ Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.
♦ Not suitable to operate in acidic environment, PH<7.
♦ LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.
When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine
element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than 375 PPM.
♦ The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.
♦ Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.
♦ Before opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. The LEDs shouldbe used within a year.
♦ After opening the package, the product should be stored at 30℃ or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30℃or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.
4000pcs/reel, each reel Anti-static vacuum Bag
Shipped in 3-5 days after payment
1. 3 years warranty
2. 5 years technical service team
3.professional sales team
4.Free Sample is available
6.Aiming at the consult of "high quality,zero defect",give you the best quality,best service.
Guangdong Elite Optoelectronic Technology Co., LTD
Contact: Carol Chen