Home » Product > SMD LED > SMD LED 5630
Product Categories

SMD 5630 Datasheet

●100% original packing
●Steady & sufficient stocks
●High-end service quality
●Prompt delivery

Send InquiryChat Now






0.5 W








Warm White,Natural White,Pure    White,Cool White

Color Temperature


Chip Size

10*30 mil,12*31 mil, 17*34 mil,


3 years


50000 hours


Ceiling light,bulb wall lamps,down light,wall    lamp,garden light ,food light, miner lamps


Low Heating Generation To Reduce Electricity    

Consumption of Air Conditioning.
Great Reducing Carbon Emission.
save power more than 95% by ordinary bulbs ,Equivalent to 35-50w Halogen Bulb.

1-100watt led white,blue,red, green,yellow color also available.
Custom size can be manufatured on request.


 Color Bin Limit (IF =150 mA)

Requirements for application and reflow soldering

Reflow Soldering




Pro-heat time


120 seconds Max.


Peak temperature


245℃ Max.


Soldering time


10 seconds Max.




Refer to Temperature-profile

After reflow soldering rapid cooling should be avoided

Temperature-profile(Surface of circuit board)  

Use the following conditions shown in the figure.   


 <Pb-free solder>                           <Lead solder>


1.Reflow soldering should not be done more than two times    

2.When soldering,do not put stress on the LEDs during heating


 > 100% original packing
 > Steady & sufficient stocks
 > High-end service quality
 > Prompt delivery


 image009(002).jpg image011(002).jpg


Packaging & Delivery

 Packaging  Details
 4000pcs/reel, each reel Anti-static vacuum  Bag

 Delivery  Time
 Shipped in 3-5 days after payment




Handling Precautions

Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.


♦ Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.


♦ Not suitable to operate in acidic environment, PH<7.


♦ LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.


When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine 

element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than  375 PPM.


♦ The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.


♦ Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.



♦ Before opening the package, the LEDs should be kept at 30 or less and 60%RH or less. The LEDs shouldbe used within a year.


♦ After opening the package, the product should be stored at 30 or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.

After-sale Service: 

 Any  Question for our products will be solved at the most prompt time,we always  offer relative technical suppport and consultant quick respons ,all your inquiry will be  replied within 24 hours.


 Q1. Can I have a sample order for led light?
 A: Yes, we  welcome sample order to test and check quality. Mixed samples are acceptable.

 Q2. What about the lead time?
 A:Sample  needs 3-5 days, mass production time needs 3-5 days for order quantity.

 Q3. Do you have any MOQ limit for led light order?
 A: Low MOQ,  1pc for sample checking is available

 Q4. How do you ship the goods and how long does it take to arrive?
 A: We usually  ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline  and sea shipping also optional.

 Q5. How to proceed an order for led light?
 A: Firstly  let us know your requirements or application.
 Secondly We quote according to your requirements or our suggestions.
 Thirdly customer confirms the samples and places deposit for formal order.
 Fourthly We arrange the production.

 Q6. Is it OK to print my logo on led light product?
 A: Yes.  Please inform us formally before our production and confirm the design firstly  based on our sample.

 Q7: Do you offer guarantee for the products?
 A: Yes, we  offer 3 years warranty to our products.







Alisa Huang

Guangdong Elite Optoelectronic Technology Co., LTD




Contact: Carol Chen



Hot Tags: SMD 5630 datasheet, China, suppliers, manufacturers, price